IJE_Vol 05 N 02
Permanent URI for this collectionhttps://archives.univ-eloued.dz/handle/123456789/22772
Browse
Recent Submissions
Item The electrical properties of Au/GaN and PEDOT: PSS/GaN diodes(جامعة الوادي - university of el oued, 2020-12-15) Sadoun, A; Kemerchou, I; Mansouri, S; Chellali, MIn the present paper, using a numerical simulator, the simulation of Au/n-GaN and PEDOT: PSS/GaN structures were performed in a temperature at room temperature. The electrical parameters: barrier height, ideality factor, shunt resistance series, and resistance have been calculated using different methods: conventional I-V, Norde, Chattopadhyay, and Mikhelashvili. Statistical analysis showed that the Au/GaN structure has a barrier height of (0.6 eV) which is higher compared with the PEDOT: PSS/GaN structure (0.72 eV) and ideality factor (1.88 and 2.26) respectively. The values of resistance shunt were increased from 77150.056 Ω to 11207586 Ω. It is observed that the leakage current increased from 6.64E-5 to 4.98926E-5A at −0.85 V.Item Performance of a wastewater treatment plant in south-eastern Algeria(جامعة الوادي - university of el oued, 2020-11-07) Khechekhouche, Abderrahmane; Bouchemal, Fattoum; Kaddour, Zineb; Salim, Khechana; Miloudi, AbdelmonemThe experimental study was carried out on an urban wastewater purification station located in the region of El Oued -Kounine- in south-eastern Algeria. During 6 months, samples were taken every month to study the Physico-chemical parameters of this station. Monthly monitoring of SS, COD, BOD5 was made from September 2017 to February 2018 and the results obtained show that the average elimination rates were 77.76, 74.10 and 80% respectively for BOD5, DCO and SS. The average of the ratio COD/BOD5 during the 6 months of follow-up is equal to 2.9.Item Numerical simulation of the flow rate effect on the evolution of a negatively buoyant water jet(جامعة الوادي - university of el oued, 2020-11-25) Eleuch, Oumaima; Latrache, Noureddine; Frikha, Sobhi; Khechekhouche, Abderrahmane; Driss, ZiedA numerical simulation study was done on a penetrating pure water jet injected into another surrounding salt water miscible with negative buoyancy conditions. For the incompressible filtered Navier-Stokes equations and the sum of the fluid model volume, we used a transient Computational Fluid Dynamics (CFD) solver (VOF model). A finite volume discretization method using Open Source code given in Open Foam 2.3.0. was used to solve these equations. The flow has a significant impact in the laminar system on the evolution of the jet in terms of subsequent permanent phase as well as transient regimeItem Numerical simulation of the flow rate effect on the evolution of a negatively buoyant water jet(جامعة الوادي - university of el oued, 2020-12-25) Allal, Abderrrahim; Khechekhouche, Abderrahmane; Driss, ZiedA numerical simulation study was done on a penetrating pure water jet injected into another surrounding salt water miscible with negative buoyancy conditions. For the incompressible filtered Navier-Stokes equations and the sum of the fluid model volume, we used a transient Computational Fluid Dynamics (CFD) solver (VOF model). A finite volume discretization method using Open Source code given in Open Foam 2.3.0. was used to solve these equations. The flow has a significant impact in the laminar system on the evolution of the jet in terms of subsequent permanent phase as well as transient regimeItem Induction machines diagnosis by the time's harmonics(جامعة الوادي - university of el oued, 2020-12-01) Allal, Abderrrahim; Khechekhouche, Abderrahmane; Driss, ZiedThe induction motor is currently becoming the key element of most industrial equipment. Despite these advantages, a certain number of constraints of very different natures can affect the lifetime of this machine, causing considerable economic losses. This work is the study experimental of defects for an asynchronous machine (with and without defect). After having described the main defects that can occur on these. In this study, we propose a method called induction machines diagnosis by the time's harmonics. This technique is based to study the influence of a defect of short-circuiting on the studied induction motor, we will find the rank of the harmonic of the most influenced by the number of the rank default. this study will find the diagnostic index of induction motor with stator default using the time harmonics. The results obtained show that the 3rd order time-harmonic is very sensitive compared to the other harmonicsItem Engineering and Economic Evaluation of Production of SnO2 Nanoparticles by Microwave-Assisted Green Synthesis(جامعة الوادي - university of el oued, 2020-12-12) Salsabila, Annida Annida; Nurfatonah, Dea Yuli; Sela, Selvian Kitin; Wardhani, Putri KusumaThe synthesis of nanoparticles from noble metals such as tin (IV) oxide (SnO2) is a research in progress with a very wide application in various fields, such as environmental improvement, gas sensors, catalysis, and lithium-ion batteries. The purpose of this study was to evaluate the economic feasibility of producing tin (IV) oxide (SnO2) nanoparticles using the microwave-assisted green synthesis method on an industrial scale for 10 years by evaluating from an engineering and economic perspective. Various economic parameters are used to analyze economic viability, including Gross Profit Margin (GPM), Payback period (PBP), Cumulative Net Present Value (CNPV), as well as economic variations in sales, taxes, raw materials, labor wages, and utilities to ascertain project viability. Technical analysis to produce 8.54 kg of SnO2 nanoparticles per day shows a total production cost of 1,982,243,613.12 IDR and a total investment cost of 1,732,590,765.12 IDR. The resulting gross profit margin is 39,231,578,268 IDR/year, the profit is relatively economical, so this project can be run for 10 years under ideal conditions. This research is expected to be a reference for technical and economic analysis of industrial scale production of SnO2 nanoparticlesItem Economic evaluation of zinc oxide nanoparticle production through green synthesis method using Cassia fistula plant extract(جامعة الوادي - university of el oued, 2020-12-15) Fatmarin, Zahra; Utami, Fidya AhdiatiFidya Ahdiati; Girsang, Gabriela Chelvina Santiuly; Mulya, Sri Zahra Mina Setyani; Fentiana, Vina Dian; Putri, Yashinta Kirana; Nandiyanto, Asep Bayu DaniThe purpose of this study was to determine the feasibility of a zinc oxide (ZnO) manufacturing project through a green synthesis method using plant extracts Cassia fistula and then evaluate it from an engineering and economic perspective. Several economic evaluation parameters are analyzed to inform the potential production of ZnO nanoparticles, such as the length of time required for an investment to return the total initial expenditure (PBP), the condition of a production project in the form of a production function in years (CNPV), project benefits and so on. The results showed that the production of ZnO nanoparticles was very prospective. Technical analysis to produce 250 kg of ZnO nanoparticles per day shows the total cost of the equipment purchased to be 21,450.00 USD. PBP analysis shows that investment will be profitable after more than three years. This project can compete with PBP capital market standards because of the short investment returns. To ensure the feasibility of a project, the project is estimated from ideal conditions to the worst case in production, including labor, sales, raw materials, utilities, and external conditions.Item Economic Evaluation of the Production of Titanium Dioxide (TiO2) Nanoparticles using the Simple Aqueous Peroxo Route Method(جامعة الوادي - university of el oued, 2020-11-20) Sukawaputri, Sukawaputri, Aldera Margianti Aldera Margianti; Fauziah, Fauziah ,Indri Ayuni Nur; Lestari, Lestarindri Puji.Arindita; Ni Putua, Yunika; Pratiw, Riska Nur; Hofifah, Siti NurThis study aims to analyze the economic evaluation on the production of TiO2 nanoparticles using the simple aqueous peroxo route method. Economic evaluation is carried out using several economic parameters, such as Payback Period (PBP), Break Even Point (BEP), and Cumulative Net Present Value (CNPV). The economic evaluation method is carried out by calculating several factors to see the potential of TiO2 nanoparticle production, such as an increase in tax prices, sales prices, and the effect of raw material prices. Based on tax evaluation, the greatest income achievement when taxed is 10%. Based on the sales evaluation, the minimum sales price so that the company does not lose is at the 90% point. Based on variations in raw material prices, an increase in raw material prices by up to 50% will not cause a loss. PBP analysis shows the investment in a short period of time, namely in the fourth year and until the 20th year the company's profits continue to increase. In conclusion, the results of the economic evaluation show good prospects. The impact of this research is the evaluation of large-scale economic data on TiO2 nanoparticles, production prospects with estimated factors that may occur under ideal conditionsItem Economic and Technical Evaluation of LifePO4 Production using Hydrothermal Method(جامعة الوادي - university of el oued, 2020-12-01) Chairunnisa, Alya; Wulandari, Sarah Ayu; Salsabila, Shafa; Putri, Silmi Ridwan; Nandiyanto, Wulan MaryamThe aim of this study is to evaluate the economic and engineering layout carried out on a factory scale LiFePO4 production using the hydrothermal synthesis method. The method used is economic evaluation by calculating gross profit margin (GPM), payback period (PBP), break-even point (BEP), internal rate return (IRR), cumulative net present value (CNPV), return on investment (ROI). , and the profitability index (PI). LiFePO4 was synthesized using precursors FeSO4.H2O, ascorbic acid and H3PO4 and then reacted with LiOH2.2H2O by maintaining the Li: Fe: P molar ratio of 3: 1: 1. The results of GPM and CNPV calculations from the manufacture of industrial scale LiFePO4 show that the payback period (PBP) has increased in the fourth year. LiFePO4 applications on an industrial scale can be used for lithium ion batteriesItem A small parabolic trough collector as a solar water heater: an experimental study in Ouargla region, Algeria(جامعة الوادي - university of el oued, 2020-11-20) Benderradji, Razik; Gouidmi, Hamza; Beghidja, AbdelhadiThis study aims to conduct an experimental thermal examination of a parabolic trough collector in Ouargla region at Algeria, which will be used as a solar water heater. The solar collector was manufactured and then experimentally tested, as its theoretical optical performance was estimated at 75.06%, while the values of its true thermal performance are 10.61, 10.68 and 8.85 % for 13 May, 14 May and 15 May. Although its thermal performance is somewhat low, the studied PTC is effective in heating the water, whereas, using a volumetric flow of 0.011 l/s, about 317 liters of water can be heated daily at 42°C, knowing that the daily average consumption of hot water in a typical house is 250 liters because the Ouargla region is strategically located that receives huge amounts of solar irradiance